Moxa ICS-G6524A Switch Driver
Description about Moxa IKS-GA-8GSFP-4GTXSFP-HV-HV-T Layer 2 Full Gigabit managed Ethernet switch with 12 10//BaseT(X) ports. MOXA ICS-GA / ICS-GA / ICS-GA Series The IKS-GA series full Gigabit backbone switches are equipped with 24 Gigabit Ethernet ports. Moxa announced a new firmware upgrade for its industrial Ethernet switches According to an ICS-CERT report, cyber-attacks on the critical.
|Supported systems:||Windows 7/8/10, Windows XP 64-bit, Mac OS X 10.X|
|Price:||Free* [*Free Registration Required]|
Moxa ICS-G6524A Switch Driver
You may add or remove IP addresses to limit access to the Moxa switch. When the accessible IP list is enabled, only addresses on the list will be allowed access to the Moxa switch. Each IP address and netmask entry can be tailored for different situations: Grant access to one host with a specific IP address For example, enter IP address with netmask to allow access to only. Grant access to all hosts Moxa ICS-G6524A Switch sure the Moxa ICS-G6524A Switch IP list is not enabled.
Remove the checkmark from Enable the accessible IP list. The following table shows additional configuration examples: Enable Checked Allows data transmission through the port. Enabled Unchecked Immediately shuts off Moxa ICS-G6524A Switch access.
The port and connected devices will determine the best speed for that connection. The final result will be determined by the Auto process between the Moxa switch and Moxa ICS-G6524A Switch devices.
Enables flow control for this Moxa ICS-G6524A Switch when the port s Speed Enable is set to Auto. Disabled Disables flow control for this port when the port s Speed Disable is set to Auto.
MOXA ICS-G7850A-2XG-HV-HV Rackmount Ethernet Switches
Moxa ICS-G6524A Switch Network Parameters Network configuration allows users to configure both IPv4 and IPv6 parameters for management access over the network. The Moxa switch supports both IPv4 and IPv6, and can be managed through either of these Moxa ICS-G6524A Switch types. A brief explanation of each configuration item is given below. A Link-Local address makes the switch accessible over IPv6 for all devices attached to the same local subnet.
To connect to a larger network with multiple segments, the switch must be configured with a Global Unicast address.
One double colon may be used in the address to indicate the appropriate number of zeros required to fill the undefined fields. GARP Moxa ICS-G6524A Switch the architecture, rules of operation, state machines, and variables for the registration and de-registration of attribute values.
Note that you need to set the same GARP timer values on all Layer 2 switches to ensure that the system works successfully. None Daylight Saving Time The Daylight Saving Time settings are used to automatically set the Moxa switch s Moxa ICS-G6524A Switch forward according to national standards.
System Up Time Indicates how long the Moxa switch remained up since the last cold start. The up time is indicated in seconds. Be sure to set the time zone before setting the time.
The time accuracy is up to 1 second, which is suitable for Moxa ICS-G6524A Switch time accuracy requirements. IEEEwhich was published in Novemberexpands the performance capabilities of Ethernet networks to control systems that operate over a communication network. In recent years an increasing number of electrical power systems have been using Moxa ICS-G6524A Switch more distributed architecture with network technologies that have less stringent timing specifications.
IEEE generates a master-slave relationship between the clocks, and enforces the specific timing requirements in such power systems. All devices ultimately get their time from a clock known as the grandmaster clock. In its basic Moxa ICS-G6524A Switch, the protocol is intended to be administration free. How does an Ethernet switch affect synchronization? The following content is taken from the NIST website at http: An Ethernet switch potentially introduces multi-microsecond fluctuations in the latency between the grandmaster clock and a slave clock.
Uncorrected these fluctuations will cause synchronization errors. The magnitude of these fluctuations depends on the design of the Ethernet switch and the details of the communication traffic.
Moxa - Your Trusted Partner in Automation
Experiments with prototype implementations of IEEE indicate that with suitable care the effect of these fluctuations can be successfully managed. For example, use of appropriate statistics in the devices to recognized significant fluctuations and use suitable averaging techniques in the algorithms controlling the correction of the local Moxa ICS-G6524A Switch will be the good design means to achieve the highest time accuracy.
A switch can be designed to support IEEE while avoiding the effects of queuing. In this case two Moxa ICS-G6524A Switch to the usual design of an Ethernet switch are necessary: The switch must be configured such that it does not pass IEEE message traffic using the normal communication mechanisms of Moxa ICS-G6524A Switch switch.
Such an Ethernet switch will synchronize clocks directly connected to one of its ports to the highest possible accuracy. This value is fixed at 0x21, which Moxa ICS-G6524A Switch the time of the EDS switch is accurate to within ns. The time unit is SI seconds, as realized on the rotating geoid SI: